Home > Windows Vista > Vista Boot Problem !

Vista Boot Problem !

Contents

REPAIR YOUR COMPUTER ends in the same blue screen that STARTUP REPAIR Does. Please wait, since this may take a while… Successfully scanned Windows Installations. November 8, 2011 Jason My computer continuosuly gets the start up problem where i have to restore to factory settings as system restore will not work, Everytime my pc turns off While I have some pretty good and basic knowledge, based mostly on experience and learning from places like this site -- I certainly do not consider myself a geek by HTG check my blog

The Windows boot manager screen allows a Windows memory diagnostic which actually completes, then restarts the computer, then goes right back to STARTUP REPAIR, which again, fails!! Otherwise, click on the Don't send option. Please try again. Your PC may be different. http://www.dell.com/support/article/SLN128762/en

Windows Vista Startup Repair Without Disk

Click on your preferred search engine below, then describe your problem, including any specific error messages. Could not repair automatically When sending this information, it is important to note that you will not receive a response back from Microsoft with a solution. No user intervention is required here. This is an invaluable tool for removing security threats such as worms, rootkits, and other malware from your computer and to be able to access files when Vista fails to boot

Lucia St. Step 6: Fix (ReBuild) the corrupted Boot Configuration Data (BCD) folder. 1. For some techniques, we'll use the Repair Your Computer option (highlighted in Figure 1), which brings up the System Recovery Options dialog box shown in Figure 2. Windows Vista Repair Tool Be patient while it finishes, sometimes it can take a while for it to complete.

Your computer will start and you should see your BIOS listing your hardware and other information. Windows Vista Repair Disk Download Attempt to restore from the most recent restore point. I follow up exactly as you explained and it works!!!! Figure : Example of a hard drive name listed in the BIOS (Western Digital) If the hard drive name is listed, refer to the steps in the section Hard drive detected.

This setting is commonly found inside “Advanced settings”. 3. Windows Vista Startup Repair Download Remove the side panel by loosening the side panel screws and sliding the panel to the back of the computer. If you're lucky, one of these steps may fix your software problem and allow you to boot Windows normally. Use the following HP support document: The Monitor is Blank after Starting the Computer.

Windows Vista Repair Disk Download

RELATED ARTICLESBeginner Geek: How to Reinstall Windows on Your ComputerEverything You Need to Know About "Reset This PC" in Windows 8 and 10 Recover Files When Windows Won't Boot RELATED ARTICLEHow Use the arrow keys to select Yes or OK and press Enter. Windows Vista Startup Repair Without Disk It will go through the motions, scan the entire disk for partitions, but won't/can't fix the problem. Windows Vista Startup Repair Not Working The only thing I did recently was download Skype.

If you receive an error from the PSA diagnostics, refer to the Dell Hardware Diagnostics page for further assistance: Click Here to Troubleshoot Diagnostic Errors Step 5: Boot the Computer into click site Figure 8. Log in as a user with administrative rights, and click OK. A Startup Repair window opens and automatically scans for startup problems. Windows Vista Not Booting Black Screen

DID YOU KNOW?The play, fast-forward, and rewind button logos were originally intended to indicate the direction the tape media would move if you pressed the button. Configure language and location options in Vista Setup At this screen you should configure the Language to install, Time and currency format, and Keyboard or input method options so that Enter the BIOS settings by pressing “DEL” or “F1” or “F2” or “F10”. * * The way to enter into BIOS Settings depends on the computer manufacturer. 2. http://relite.org/windows-vista/boot-problem-on-vista-home-premium.php I found another screen called EDIT BOOT OPTIONS (F10 tapping?) and tried CHKDSK : /F on someones advice but it rebooted and I ended up back where I started.

Click the link below to being the troubleshooting process: How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7 Step 10: Restore the Operating Windows Vista Recovery Without Disk Click below to change the operating system. I was going to uninstall it again because it suddenly recovered the last Skype account I had and I have NO IDEA HOW!?

Step 9: Use Clean-Boot Troubleshooting to Isolate the Software Issue A program or application may be interfering with the normal boot process of Windows.

Note: Not using Windows Vista? Save and Exit Bios Setup. If you haven't been messing around inside the case, it's possible the power supply is dead. Windows Vista Startup Repair Loop Figure 6.

Select Diagnostics to start the diagnostic assessment of the computer hardware. Status BAD, Backup and Replace. If your computer does not boot to Safe Mode, select from the following options to troubleshoot. http://relite.org/windows-vista/vista-boot.php Getting blue screen memory dumps on shutdown, and hanging after seeing the "Starting Windows" screen on startup.

Just like a battery on a watch, the computer has a battery on the motherboard to back up time and settings when the computer is off. These tools are: Startup Repair Startup Repair is an automated repair process that scans your Vista installation for problems and attempts to automatically fix them. I can't just recover because I'd love my photography! Find the power cable connected to the hard drive.

Startup Repair window The automatic repair process can take quite a while. BEST OF HOW-TO GEEK 10 Quick Ways to Speed Up a Slow PC Running Windows 7, 8, or 10 How to Fax a Document From Your Smartphone 10 Important Computer Security After a while, the status bar will turn completely white and you will see a screen stating that Windows is loading.